TERMINATION Datasheet(PDF) - RT9088 - Richtek Technology Corporation

Electronic Components Datasheet Search

ALLDATASHEET.COM

X

TERMINATION Datasheet, PDF

Searched Keyword : 'TERMINATION' - Total: 17 (1/1) Pages

Manufacturer	Part #	Datasheet	Description
Richtek Technology Corp...	RT9088	231Kb/11P	DDR Termination Regulator
	RTQ2536-QA	211Kb/11P	DDR Termination Regulator
	RT9089A	195Kb/10P	DDR Termination Regulator
	RT2568	232Kb/11P	DDR Termination Regulator
	RT9173B	262Kb/13P	2A Bus Termination Regulator
	RT9173	198Kb/10P	1.5A/3A Bus Termination Regulator
	RT9173	306Kb/13P	Peak 3A Bus Termination Regulator
	RT9005A	208Kb/10P	DDR VDDQ and Termination Voltage Regulator
	RT9173C	225Kb/13P	Cost-Effective, 2A Sink/Source Bus Termination Regulator
	RT9045	180Kb/11P	Cost-Effective, 1.8A Sink/Source Bus Termination Regulator
	RT9173D	223Kb/13P	Cost-Effective, Peak 3A Sink/Source Bus Termination Regulator
	RT9089AGQW	851Kb/8P	The RT9089A is a sink/source tracking termination regulator
	RT9199	204Kb/13P	Cost-Effective, 2A Peak Sink/Source Bus Termination Regulator
	RT2568GQW	828Kb/8P	The RT2568 is a sink/source tracking termination regulator
	RT9088GQW	803Kb/8P	The RT9088 is a sink/source tracking termination regulator
	RT9173D_0712	223Kb/13P	Cost-Effective, Peak 3A Sink/Source Bus Termination Regulator
	RT9210	349Kb/17P	Dual 5V Synchronous Buck DC-DC PWM Controller for DDR Memory VDDQ and VTT Termination

1

1

What is TERMINATION

Termination in electronic components means electrical termination.

It is commonly used to reduce signal-damaging reflections on the transmission line of electromagnetic waves.

For example, when sending a signal on a cable or printed circuit board (PCB), the signal travels to the end of the cable or PCB.

At this point, when the signal hits the end, some of the signal may be reflected and collide again.

These reflections can cause signal corruption and reduced speed.

Termination is therefore used to minimize these reflections and reduce signal noise from the ends.

Termination is usually implemented using resistors, capacitors or diodes.

A resistor of 50 ohms is usually used to close the ends.

This minimizes signal reflections and speeds up the transmitted signal.

*This information is for general informational purposes only, we will not be liable for any loss or damage caused by the above information.

ALLDATASHEET.COM

Does ALLDATASHEET help your business so far? [ DONATE ]

About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List
All Rights Reserved©Alldatasheet.com

Mirror Sites English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz

Family Site : ic2ic.com | icmetro.com