Electronic Components Datasheet Search
  English  ▼
ALLDATASHEET.COM

X  



TERMINATION Datasheet, PDF

Searched Keyword : 'TERMINATION' - Total: 12 (1/1) Pages
ManufacturerPart #DatasheetDescription
Company Logo Img
Fairchild Semiconductor
ML6553 Datasheet pdf image
115Kb/7P
Bus Termination Regulator
ML6554 Datasheet pdf image
386Kb/14P
3A Bus Termination Regulator
FAN6550 Datasheet pdf image
99Kb/12P
2A DDR Bus Termination Regulator
FAN6555 Datasheet pdf image
116Kb/12P
2A DDR Bus Termination Regulator
FAN1655 Datasheet pdf image
494Kb/9P
3A DDR Bus Termination Regulator
FAN1655 Datasheet pdf image
513Kb/9P
3A DDR Bus Termination Regulator
FAN1654 Datasheet pdf image
80Kb/7P
1.5A LDO, DDR Bus Termination Regulator
FAN23SV04TMPX Datasheet pdf image
1Mb/17P
FAN23SV04T TinyBuck 4 A Integrated Synchronous Buck Regulator for DDR Termination
FSA110 Datasheet pdf image
389Kb/2P
Audio and Wired-OR USB2.0 Hi-Speed(480Mbps) Switch with Negative Signal Capability and Built-in Termination
FSA110 Datasheet pdf image
619Kb/2P
Audio and Wired-OR USB2.0 Hi-Speed(480Mbps) Switch with Negative Signal Capability and Built-in Termination
FSA321 Datasheet pdf image
447Kb/2P
USB2.0 Hi-Speed (480Mbps) and Audio Switches with Negative Signal Capability and Built-in Termination on Unselected Audio Paths
FSA321 Datasheet pdf image
590Kb/12P
USB2.0 Hi-Speed (480Mbps) and Audio Switches with Negative Signal Capability and Built-in Termination on Unselected Audio Paths

1


1



What is TERMINATION


Termination in electronic components means electrical termination.

It is commonly used to reduce signal-damaging reflections on the transmission line of electromagnetic waves.

For example, when sending a signal on a cable or printed circuit board (PCB), the signal travels to the end of the cable or PCB.

At this point, when the signal hits the end, some of the signal may be reflected and collide again.

These reflections can cause signal corruption and reduced speed.

Termination is therefore used to minimize these reflections and reduce signal noise from the ends.

Termination is usually implemented using resistors, capacitors or diodes.

A resistor of 50 ohms is usually used to close the ends.

This minimizes signal reflections and speeds up the transmitted signal.

*This information is for general informational purposes only, we will not be liable for any loss or damage caused by the above information.


Link URL :

Privacy Policy
ALLDATASHEET.COM
Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Datasheet Upload   |   Contact us   |   Privacy Policy   |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com